Biomass Magazine reporting about our Hurricane cyclone - ACS

Biomass Magazine - The Utility of Cyclones

Jun 2015

"Cyclones have been around for more than 100 years, with the first patent issued in 1886. "They have been used ever since to separate particles from an air, gas or liquid stream without the use of barrier filters across a wide range of industries," says Pedro Araujo, CEO and cofounder of Advanced Cyclone Systems S.A. The Portugal-based company is exclusively dedicated to the development and commercialization of high-efficiency cyclone systems worldwide. "Cyclones do not function differently depending on the applications," Araujo says. "The fundamental principles remain the same."
Andy Cowan, vice president of Rees-Memphis Inc., says while the technology is old, cyclones have been relied upon for a long time because they are good at what they do. "They're a separator to redirect and make air do what you want it to do," Cowan says. "Dust will drop out, and you have clean air coming out."

The primary function of cyclones is to separate dust particles from an air or gas stream. Mike Clark, regional sales manager for CECO Environmental, says two primary factors influence cyclone performance: centrifugal force and residence time. "The typical industrial cyclone is a centrifugal reverse-flow cyclone," Clark says. "Dirty gas with particulates enters the top and it spins around the body of the cyclone, down the cone, and the particles are forced alongside the wall of the cyclone and are collected." Araujo says in air-solid cyclone separation processes, the gas and particles enter tangentially through the top, and high-speed rotation flow "throws" the solid particles against the wall?"a consequence of the higher inertia of the solid particles relative to the gas particles," he says. "As the air stream approaches the bottom of the cyclone after going down, it inverts the direction in the Y axis, though maintaining the same rotation, and escapes the cyclone by a vertical outlet, or vortex finder, on the top." It is this inversion of movement that gives the name "reverse flow" to these kinds of cyclones. Cowan says air follows the path of least resistance, so once this inversion of movement happens at the bottom of the cyclone, the cleaned air escapes through the larger opening at the top?the least-resistant route.
Positioned at the bottom of a cyclone is either an expansion chamber, dust receiver or vortex breaker, which allow the particles to disengage from the spinning gas stream and exit through an airlock or feeder while the cleaned air turns up the center of the cyclone and out the top. The outlet air exits either to the atmosphere or other downstream equipment such as a baghouse, scrubber, or wet or dry electrostatic precipitator (ESP), depending on the application, emissions standards and more.
"What affects operational efficiency as the gas stream is spinning is centrifugal force?a measure of the force applied when spinning?so the faster the inlet air speed, and the smaller the cyclone body diameter, the more force there is pushing particles to the wall for collection," Clark says. "How long that force is allowed to act on the particles determines how much of the particles will be collected, especially the fine particles." The larger the particle size, the more efficient the cyclone. "There is a fractional efficiency curve associated with the efficiency of a cyclone," Clark says. "If you have a dust distribution stream that is course, you can use a lower-efficiency cyclone to achieve a given collection efficiency. If it's a very fine dust, like flour or talcum powder, then it takes a much more efficient cyclone to achieve the same efficiency by weight."
Motorized fans, positioned either on the clean or dirty side of the cyclone, provide the energy to power the vortex effect. A positive cyclone system is one in which a material-handling fan blows into the cyclone, Cowan explains, whereas a negative cyclone system operates with a fan on the clean side, sucking clean air out versus pushing particle-laden air in. Cowan says the negative system is more efficient. "If you put a fan on the positive side blowing into cyclone, you don't need a rotor airlock at the bottom of the cyclone," he says. In the wood industry, one reason not to have the fans on the positive side is, if the fan does not have the abrasive particles constantly flowing through it, there is less wear to consider. "But they tend to work better on the positive side," says Cowan, adding that if a filter follows the cyclone, then the fan setup is typically positioned for negative pressure.
Fans can be considered part of the cyclone system, Cowan says, but in large mills where there is a lot of waste, the fan systems are separate units. "In those, we put them on the ground where we can maintain them," he says. "The biggest one I've ever seen where it's part of the cyclone is about 50 horsepower, set up as a negative pressure system pulling cleaned air through."

Size and Efficiency
Increasing the force on the particles demands more energy, which Clark says comes in terms of pressure drop across the cyclone. "For cyclones in the wood industry, whether it's for a pellet dryer or other application, there is a practical limit to the amount of energy one can apply to meet environmental standards," Clark says. "You need to increase residence time, or the amount of time it takes to travel to the wall of the cyclone, and when you do that, the cyclone gets bigger and more efficient."
According to Cowan, a tradeoff exists between efficiency of separation and energy consumption. "It takes a lot more energy for a cyclone to be more efficient," he says. To design a more efficient cyclone with a longer body and smaller diameter, then the static pressure?or the resistance in a system?goes up, Cowan explains, which requires more horsepower to move the air through at the velocity needed. As a result, energy consumption increases. "It takes horsepower to overcome that resistance," he says.
Clark says CECO Environmental's ultrahigh efficiency series cyclones are nearly double the size of its standard efficiency series. Interestingly, however, Clark says energy consumption for the ultra-high efficiency series is actually lower than its standard efficiency series.
Cyclones are ideal for many wood operations, including various biomass applications. "Cyclones are excellent with larger chips, shavings, bark?the larger particles," Cowan says. "In the wood industry, cyclones are very prevalent. Heavy chips and big particles, they drop out and do not get entrained in the air, whereas light dust can get off the wall, go back through the top and exit the cyclone. With really light, fine dust, even the most efficient cyclones will just blow it out the top."
Depending on the type of particles, and the type and design of the cyclone, they can be efficient enough in certain applications. "If it is efficient enough to separate and the horsepower isn't too high?meaning energy consumption is efficient too?then a cyclone is the best way to go because, compared to a filter, it has the lowest operation and maintenance costs," Cowan says. "But if the dust gets to be so fine that a cyclone can't efficiently separate what you want, then have you to use a baghouse following the cyclone."
Clark says if it is certain a baghouse will be downstream of the cyclone, one should be selective and discerning in how efficient the cyclone is preceding the baghouse. "If it's very efficient and the only thing the filter will see is very fine particles, then this can be very challenging for the baghouse," Clark says. "So, if you have a baghouse downstream, you want to select a lower-efficiency cyclone so the baghouse sees bigger particles to make it less challenging." Consider it a Goldilocks situation in which the cyclone is required as to not inundate filters with too much material, but the cyclone cannot be too efficient as it's also a problem if only fine particles are entering the baghouse. "It comes down to particle size distribution versus emission requirements," Clark says. "In addition to particle size, there's the aerodynamic properties to consider?wood flakes are different than lead shot. If lead shot were the same physical size, it's obviously much heavier and spherical, whereas wood flakes are more challenging because they are lighter and float around in the air stream, and therefore, they are more difficult to collect. We can determine the aerodynamic distribution from a representative sample, and given this inlet loading, we can meet the given outlet loading with a particular cyclone."
CECO Environmental's ultra-efficient cyclones can take the place of a baghouse, Clark says. "That's not to say cyclones are as efficient as a baghouse," he says, "but there may not be enough fine particles in the stream for those to be needed. We have cyclones on pellet dryers going to atmosphere without any downstream equipment. If there's a scrubber or wet ESP, the cyclone will help lower dust loading to lower water consumption on a scrubber or wet ESP, which has to be discharged, so the amount of water discharged is directly related to the amount of loading on the front-end. That's one advantage of a high-efficiency cyclone before a Venturi scrubber or wet ESP." Also, a cyclone can help reduce particle loading in a wet ESP to keep emissions down and meet requirements. "If a standard cyclone is collecting 9.5 pounds an hour, a high-efficiency cyclone may collect 9.9 pounds an hour, which just cut emissions coming out of the cyclone by 80 percent," Clark says. "Now, the wet ESP or scrubber doesn't have to work so hard, and they consume less water and less energy." In 2008, CECO Environmental acquired Fisher-Klosterman, which produces cyclones and scrubbers.
Cyclones typically do not follow biomass boilers for fly ash removal. "Boilers have fly ash, and that is challenging for cyclones," Clark says. "We've done it with a high-efficiency cyclone and a Venturi scrubber with high pressure drop. Typically what you see following a boiler is a multiclone followed by a wet ESP." A multiclone, Clark explains, is like a baghouse but instead of bags, it uses a bunch of small axial-flow cyclones.
Araujo says cyclones are easily manufactured to withstand all kinds of extreme operating conditions, including high temperature and abrasive or corrosive environments. As a result, they are commonly used as preseparation equipment for several reasons, including to remove silica or larger particles to reduce abrasion in the downstream equipment. "This is done across a wide range of industries," Araujo says. Cyclones are also used to reduce sparks and glowing particles in wood-drying processes for safety reasons. "This is typically seen in wood and wood derivative processing companies prior to the dryers," he says. And, as Clark points out, they're used to reduce particle load into downstream equipment to help meet emissions limits or alleviate the work load into final stage emissions control equipment.
"Cyclones can be very useful for preseparation before other technologies, such as bag filters or ESPs," Araujo says. "For bag filters it is very important to reduce load of abrasive particles, which can damage the filter elements, and especially glowing particles, which can cause pinholes in filters, or even fires. ESPs may also have problems with very high particulate concentrations due to Corona Suppression of the electrical field. Basically, if a well-designed cyclone removes the main fraction of particles, the electrical field can be used to treat exclusively the very small particulate that cannot be separated by centrifugal forces. The efficiency of the complete arrangement of a cyclone plus ESP is therefore much higher for the same investment." 
In most common small to medium biomass combustion-to-power applications, the setup is a boiler, followed by a multiclone and then a bag filter or an ESP before the stack. "ACS high-efficiency cyclones are so revolutionary that we replace bag filters and ESPs," Araujo says. "We do not compete against other cyclone manufacturers, but against other technologies." He says ACS cyclone systems are completely new, and benefit from several competitive advantages. "Their main benefits arise in industrial applications where bag filters have problems, such as high temperature or pressure, condensation and cross-contamination, or high costs like expensive filter media and frequent change of bags," he says, adding that regular cyclones are not efficient enough and the costs of ESPs are unbearable, or the equipment is technically just not applicable. 
"In emission control applications, cyclones up to now have been mainly used as preseparation systems to reduce the load going into secondary filtering systems such as bag filters and ESPs," Araujo says. "ACS's Hurricane and ReCyclone systems contradict the general thinking that cyclones are inefficient powder collectors. ACS's cyclone systems can replace bag filters and ESPs in many demanding operating processes." 

Customer Needs, R&D, Simulations
Some manufacturers design custom-made cyclones for specific applications, but the cost is much greater. "We can't sit down and design a cyclone for every single customer and application," Cowan says. "Some will do that. The customer will say we need this and that, and they are willing to pay $70,000 on just one cyclone. This starts with a particle size distribution analysis." Computer programs can then take that data, density and velocity of air, to design a cyclone for a specific application. "It's very costly to do, plus these customers want performance guarantees," Cowan says. "There are a few companies that will provide guarantees, but you're paying a lot of money for that. The parameters have to stay constant all the time."
Clark says it's difficult to perfect an equation to predict the performance of cyclones. He says when Fisher-Klosterman launched its XQ series in the early 1980s, the company conducted empirical lab testing to determine the fractional efficiency curve of cyclones, and how it relates to gas density and viscosity. "If a customer comes to us, we take a sample of their dust and convert it to aerodynamic distribution and overlay that data on curves we developed empirically," he says. "Then, we guarantee removal percentage by weight. We've been doing this for 40 years?and guaranteeing performance."

ACS uses specialized modeling and numerical optimization to manufacture an optimized family of cyclones. "ACS's cyclones are better due to our specialized scientific knowledge in particle agglomeration modeling?PACyc?and numerical optimization in partnership with the engineering faculty of Porto, where we run a pilot system for R&D," Araujo says. "The revolutionary concept of particle agglomeration is essential to explain how cyclones really work and, consequently, to optimize them. The outcome of our research is not a universal solution, but a set of very different cyclone families and systems serving particular client needs and customizable for each given application." 
Using PACyc modeling while considering several economic and operational constraints such as size and pressure loss, Araujo says it is possible to affordably simulate millions of virtual prototypes with numerical optimization. "Considering this approach as the best path to obtain truly optimized cyclones, sound theories of cyclone collection and pressure loss were chosen for each process application," he says. "These numerical optimization problems have resulted in several families of cyclones, some of those patented. Indeed, different industrial cases have different needs for which the optimization functions to incorporate in the PACyc model may be as complex as minimizing cost or space, subject to a minimum efficiency result. Our cyclone families, always subject to further customization, are the result of very different client demands ACS has come across to date. Unlike most cyclone providers, we give strict guarantees of emissions and efficiency."

ACS has installed systems for various biomass applications, such as combustion boilers, pyrolysis, gasification, pelleting and drying. The company completed nearly 200 projects in the past seven years, which helped ACS "develop a complete line of very different hurricane cyclone families for each different need, considering how interparticle agglomeration/clustering affects collection efficiency," Araujo says. "From coarse particle preseparation proportioned by compact and low pressure drop cyclones, such as our SD and DX lines, to fine particulate capture with high-end geometries such as the EX and MK, ACS provides solutions for a wide range of industrial cases, being able to reach emissions comparable to ESPs." 
Although Rees-Memphis doesn't custom-make cyclones or provide performance guarantees, the company relies on basic designs that, over time, have proven to work in certain applications. Through experience and adjustment techniques, such as baffling at the bottom of the cyclone to help direct air out, Rees-Memphis helps guide the customer, who knows up front there is no performance guarantee.

Life and Maintenance
With no moving parts, maintenance on cyclones is fairly low. "It's mostly spot-checking, making sure there's no holes or wear anywhere," Cowan says. "We might replace an elbow in the dust collector once every four months. We do build cyclones with stainless steel abrasion liners at the inlet that can be removed if need be."
Abrasion is often the main concern. "The more material coming through it, the more abrasion you have," Clark says. This can be mitigated by material selection with abrasion-resistant materials in key areas, or building in replaceable sections where known wear will occur. He says if the velocity, centrifugal force and pressure drop are too great, this will cause premature wear. "There is a practical limit," he says.
In most biomass applications where abrasion is not a factor, the maintenance requirements are usually limited to visual inspections every six to 12 months to ensure there is no plugging, condensation or unexpected material accumulation, Araujo says. "There is only maintenance of the rotary valves, as any other valves following the respective manufacturers' recommendations," he says.
Painting the cyclones is another routine maintenance practice to increase the longevity of the system, Cowan says. In addition, inspection of the fan systems, including looking for loose belts, feeling for unusual vibrations, which may mean something is hung up on the wheel; and making sure the motor has proper lubrication, if required; and the bearings are greased and not running hot, are all part of sound routine maintenance practices.
With proper maintenance and rework as needed, cyclones can last decades. "Some of ours have been out there in the field for more than 20 years," Clark says.
ACS designs its systems to last at least 10 years. "Our main concern is abrasion, which may happen for many types of biomass combustion, for instance, due to the silica content of the ash and course particle size," Araujo says. "For this reason, we usually place our systems after any basic preseparator, for example, a low-efficiency, low pressure drop multiclone, which can easily capture the big and more aggressive particles, leaving the fine particulate to be handled by one of our most efficient product lines." 

Latest collaboration with Biomass Magazine. You can read the full article in the link below. 

Author: Ron Kotrba
Senior Editor, Biomass Magazine